Data Cabling & Network Installation in Sydney & the Sutherland Shire
The backbone your security and IT both rely on: structured cabling, comms racks, managed switching, Wi-Fi and point-to-point links. Clean, certified and documented — so cameras, controllers and devices have the bandwidth and segmentation they need.
Bioni Security & Electrical installs Cat6 and Cat6A structured cabling, comms racks, managed switching and Wi-Fi for offices, warehouses, schools and strata sites across Sydney and the Sutherland Shire, from one extra data point to a full fit-out. Every link is tested, certified and labelled, and one licensed team runs and certifies the rack's power circuits.
For offices, warehouses, medical suites, schools and strata sites that need cabling done once and done properly — a fit-out, an extra bank of desks, a comms cupboard that's become a bird's nest, or a link to a building the Wi-Fi can't reach. We design and install Cat6 and Cat6A structured cabling, build and patch comms racks, configure managed switching with VLANs and PoE budgets that actually add up, and put in Wi-Fi and outdoor point-to-point links where cable can't go.
Data cabling is where our security and electrical trades meet, and one Caringbah-based licensed team pays off here: the crew certifying your outlets is the same crew that hangs cameras, wires access control and runs the power circuits the rack needs — one contractor, one labelling scheme, one set of documentation. Every installation across Sydney and the Sutherland Shire is tested, certified and labelled, so the next tech who opens your rack — ours or anyone else's — knows exactly what goes where.
Data Cabling: what's included
- Extra data points, network points and Ethernet outlets in existing rooms
- Cat6/Cat6A structured cabling and certification
- Comms racks, patching and labelling
- Managed switching, VLANs and PoE budgeting
- Wi-Fi and outdoor point-to-point links
Data Cabling: how we work
Free site visit
We walk the floor plan with you, count outlets, check ceiling and riser access, and work out where the rack should live and what power and cooling it needs. Free within 100 km of Caringbah.
Design & itemised quote
You get a cabling schedule and an itemised ex-GST quote — outlets, cable grade, rack hardware, switching and patching listed line by line, so adding or trimming outlets is a visible line item, not a mystery variation.
Installation
Cable pulled on proper paths clear of power and interference, terminated and dressed at both ends, the rack built and patched, and any new power circuits for the rack run under our electrical licence.
Certification & handover
Every link is tested and the cable certification results handed over with your documentation — labelled outlets, patch schedule and switch configuration — so the installation is proven, not presumed. Failed links get fixed before we leave, not logged for later.
Optional maintenance
As you add desks, cameras or access points we extend the same scheme — and periodic rack tidy-ups, firmware updates and PoE-budget checks keep the network performing the way it did at handover.
Compliance & licensing
Data cabling in Australia is regulated work — ACMA cabling registration requirements apply to fixed cabling that connects to the telecommunications network, and we carry out cabling work in line with those requirements. Where a job includes licensed electrical work — new circuits for a comms rack, dedicated power for network equipment, relocating outlets — it's done under NSW Electrical Contractor Licence 350318C, designed with reference to the AS/NZS 3000 wiring rules, and a Certificate of Compliance for Electrical Work (CCEW) is issued.
Bioni also holds NSW Security Master Licence 000108088, which matters more than it sounds on a data job: camera, access-control and intercom cabling is security work as well as cabling work, and running it all under one licensed contractor keeps accountability in one place. Test results, labelling and documentation are part of the handover on every job — certification is what makes a cabling warranty worth something.
A recent job
An office fit-out in Hurstville
An accounting practice moving into a Hurstville office suite inherited a mess: a handful of aged outlets of unknown grade, an unlabelled patch panel in a cupboard, and a fit-out deadline four weeks out. They needed forty-odd outlets across desks and meeting rooms, Wi-Fi covering the whole floor, and cameras and door access done in the same window.
We ran new Cat6A to every desk and ceiling point, built a wall-mount rack with a managed PoE switch, and put the cameras, door controller and access points on their own VLANs, separated from the practice network. Every link was certified and the results handed over with a labelled patch schedule. The fit-out opened on time — and when their IT provider remoted in to stand up the servers, the documentation answered most of their questions before they rang us.
What moves the price
Structured cabling is quoted itemised ex-GST, per outlet and per item of rack hardware. What moves the number:
- Outlet count — the biggest single driver; each outlet is its own line on the quote
- Cable grade — Cat6 covers most offices; Cat6A costs more per metre and per termination but carries 10 Gb and higher PoE loads
- Rack work — a wall-mount cabinet with one switch versus a floor rack with structured patching and UPS power
- Ceiling and riser access — clean accessible ceiling space pulls fast; solid ceilings, occupied floors and tight risers slow every run
- Switching and Wi-Fi — managed PoE switching, access-point count and any outdoor point-to-point links
- After-hours windows — occupied offices often need pulls done outside business hours
Cabling is cheapest while walls and ceilings are open — if you're fitting out, get us in before the plasterboard goes on.
Frequently asked
- Do you certify the cabling?
- Yes — structured cabling is tested and certified, with results documented for your records and warranty.
- Can you segment cameras from the office network?
- We design VLANs and switching so surveillance, access control and corporate traffic are properly separated for security and performance.
- Should I run Cat6 or Cat6A?
- Cat6 handles gigabit and most PoE comfortably and suits the majority of offices. Cat6A is worth the premium for 10 Gb backbones, high-power PoE and Wi-Fi points you'll upgrade over the cable's life — we'll often quote a sensible mix rather than one grade everywhere.
- What drives the cost of a cabling job?
- Outlet count first, then cable grade, rack hardware and how hard the ceilings are to work in. Because the quote is itemised ex-GST per outlet, scaling the job up or down stays transparent.
- How much does it cost to install a data point?
- Per outlet, itemised ex-GST. The thing worth knowing is that the first point carries the attendance and the setup — getting to site, opening up the ceiling or cavity, setting up at the rack or router end — so the second, third and fourth points on the same visit cost materially less each than the first. After that it's how far the run is, whether the ceiling space or wall cavity is accessible or blocked, and Cat6 versus Cat6A. Termination and certification are in the per-outlet price, not billed on top. We quote per outlet after a free site visit, so you can add or drop points and watch the total move line by line.
- Can you add a data point to a room that doesn't have one?
- In most homes and offices, yes. The run comes through the ceiling space above a manhole, down a wall cavity, through spare capacity in existing conduit, or in skirting or surface duct where the cavity is blocked by insulation, noggins or fire-rated construction. A double-brick wall or a second storey changes the route we take, not whether it can be done — it just shows up in the quote. The new outlet is terminated, tested and certified exactly like any other. Where a cable genuinely can't be got there, we'll say so at the site visit and the fallback is a cabled access point at the nearest reachable location rather than a run that was never going to work.
- How long does a cabling fit-out take?
- A small office of 20–40 outlets typically takes two to four days including rack work and certification. Larger fit-outs are staged around the builder's program — we'd rather cable before the ceilings close than fight them afterwards.
- Can our IT person run the cabling instead?
- Fixed cabling that connects to the telecommunications network is regulated work under ACMA cabling rules — it isn't a DIY or IT-support task, and uncertified runs routinely fail when pushed to gigabit or PoE. Patch leads and plug-in gear are fine to self-manage.
- Can the same cabling carry cameras and access control?
- Yes — that's the point of structured cabling. Surveillance, access and corporate traffic ride separate VLANs over the one physical plant, with the PoE budget sized so cameras and access points never brown out the switch.
Reviews from Google
What our customers say.
We couldn’t be happier with the work and service provided by Bioni Electrical and Islam in particular. He has completed a number of jobs around our home and every time the quality of his work and attention to detail have been outstanding. He installed a new antenna, replaced and upgraded lights throughout the house, installed garden lighting in the backyard and carried out all the electrical work required when we converted a garage into a music studio. He also recently helped us with the installation of a heated towel rail. What really impressed us was not only the quality of the workmanship but how functional, neat and well thought-out everything was. He was reliable, professional, knowledgeable and always took the time to make sure the job was done properly. We have been extremely impressed with the level of service and would have no hesitation recommending Bioni Electrical to anyone looking for a reliable and skilled electricians. We will definitely be using their services again in the future.
Absolutely outstanding service! They installed an EV charger for my Mazda 6e and had previously completed other electrical work for us. Everything was done professionally, neatly and to the highest standard. Reliable, friendly and excellent value. Highly recommended!
Great service - very professional and extremely efficient, highly recommend!
Recently had Bioni install an alarm system at our business and couldn't be happier. Andrew and the crew turned up on time, worked cleanly, and took the time to walk me through exactly how everything works before they left. No mess, no pressure, and the pricing was upfront with no surprises. It's been running perfectly since. Would recommend to anyone looking to secure their place!
Great service from start to finish. Thanks guys.
Where we do this work
Data Cabling & Network Installation in Caringbah, Kirrawee, Menai, Hurstville, Sydney CBD, Inner West — and the rest of our service areas.
Licences, registrations and coverage
- Installing since
- 2013
- NSW Security Master Licence
- 000108088
- NSW Electrical Contractor Licence
- 350318C
- ABN
- 86 628 597 946
- NSW Government supplier
- 12432577
- Depots
- Caringbah & Nowra
- Free site visit
- Within 100 km